Skip to content

sales@wideimagesolutions.com

Phone Number: +1 (214) 727 6289                             WhatsApp Number: +1 (214) 727-6289
Please email whenever possible to make the process quicker and easier for everyone.
Email: sales@wideimagesolutions.com    Phone and WhatsApp Number: +1 (214) 727-6289.
Please email whenever possible to make the process quicker and easier for everyone.

Error Codes - Designjet 800 42'' (A0) Printer (C7780B)

*High quality colour printing for technical & business customers - printing drawing plans, illustrations, schematics & presentations*

01:10

Electronics Module failure.

Requires Service Engineer

01:11

The Electronics Module Cooling Fan badly connected.
Switch the Printer Off and wait a few minutes. Switch the Printer On again and check if the Error Code has disappeared.

If the Error Code continues, requires Service Engineer

01:12

The EEROM is not configured correctly (the product number may be missing).
Requires Service Engineer

01:13

Electronics Module failure.
Switch the Printer Off and wait a few minutes. Switch the Printer On again and check if the Error Code has disappeared.

If the Error Code continues, requires Service Engineer

02:10

Carriage failure.

Call service engineer

02:13

Carriage failure.
Switch the Printer Off and wait a few minutes. Switch the Printer On again and check if the Error Code has disappeared.

 If the Error Code continues, requires Service Engineer.

03:10

Problem with the Power Supply Unit.
• Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power ON the Printer. 

 If the System Error continues requires a Service Engineer.

04:11

LAN Card not detected.
Requires Service Engineer

05:10 (Only applicable to DJ 800 Series)

Formatter failure Error/Formatter not detected Warning.
Requires Service Engineer

05:11

Formatter not detected.
Requires Service Engineer

08:11

Problem with the Front Panel/Front Panel cannot be detected.

• Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power ON the Printer.
• If the System Error continues requires a Service Engineer.

11:11

Trailing Cable is badly connected.

Requires Service Engineer.

11:13

Problem with setting the voltage of the Printheads.
Requires Service Engineer

12:11

A short detected in the Carriage Assembly.
Requires Service Engineer

21:10

Service Station failure.

Requires a Service Engineer.

21:11

Service Station/Aerosol Fan cannot be detected or the Service Station is badly adjusted.
Requires Service Engineer

22:10

Ink Supply Station failure.

Requires Service Engineer

41:10

Electrical fault in Media-Axis Motor.
Try the following:

  • Switch the Power OFF from the back of the Printer and disconnect the Power cord.
  • Reconnect the power cord and power ON the Printer. 

If this does not resolve the problem - requires Service Engineer.

41:13

Error in the Paper-Axis Motor Encoder quadrature.
Requires Service Engineer

42:10

Electrical fault in Scan-Axis Motor.
Try the following:

  • Switch the Power OFF from the back of the Printer and disconnect the Power cord.
  • Reconnect the power cord and power ON the Printer. 

If this does not resolve the problem - requires Service Engineer.

43:10

Vacuum Fan has Stopped.
• Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power ON the Printer.
 If the System Error continues requires a Service Engineer.

43:11

Vacuum Fan not detected.
Requires Service Engineer

56:10

Drive Roller Encoder Sensor error.
Requires Service Engineer

56:13

Error in the Drive Roller Encoder Sensor quadrature.
Switch the Printer Off and wait a few minutes. Switch the Printer On again and check if the Error Code has disappeared.  If the Error Code continues Requires Service Engineer

61:04

Firmware Error.
Switch the Printer Off and wait a few minutes. Switch the Printer On again and check if the Error Code has disappeared.  If the Error Code continues Requires Service Engineer

61:05

Error Processing Job. This Error Code only appears in HP DesignJets 800 Series, or in the HP DesignJet 500 Series with an HP-GL/2 card installed, when processing either a PostScript or HP-GL/2 file.
Switch the Printer Off and wait a few minutes. Switch the Printer On again and resend the file that you were trying to print. If the Error Code reappears after resending the file, then try generating the file again and try to print again. If the Error Code continues Requires Service Engineer

64:04

Firmware Error (USB Port).
Switch the Printer Off and wait a few minutes. Switch the Printer On again and check if the Error Code has disappeared.

 If the Error Code reappears, requires a Service Engineer.

71:04

Problem allocating Memory. This Error Code only appears in HP DesignJets 800 Series, or in the HP DesignJet 500 Series with an HPGL/ 2 card installed.
Switch the Printer Off and wait a few minutes. Switch the Printer On again and check if the Error Code has disappeared.  If the Error Code reappears, requires a Service Engineer.

71:06

Out of Memory problem. This Error Code only appears in HP DesignJets 800 Series, or in the HP DesignJet 500 Series with an HP-GL/2 card installed, when processing either a PostScript or HPGL/ 2 file.
Requires Service Engineer

72:04

Problem in the Scan-Axis (Firmware Error).
Switch the Printer Off and wait a few minutes. Switch the Printer On again and check if the Error Code has disappeared. If the Error Code reappears, requires a Service Engineer.

73:04

Servo Error.
Switch the Printer Off and wait a few minutes. Switch the Printer On again and check if the Error Code has disappeared.

 If the Error Code reappears, requires a Service Engineer.

79:04

Generic Firmware error.
• Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power ON the Printer.
• Check that the Printer has the latest Firmware version. 

If error persists, requires a Service Engineer 

81:01

Paper-Axis shutdown/ Paper Servo shutdown - usually a paper-jam caused by a blockage of the Paper-axis System.

If this error code was caused by a paper-jam, unplug the power cable from the printer and clear the blockage. Plug in the power cable again and check if the Error Code has disappeared.

If this error code appeared but was NOT caused by a paper jam - requires a Service Engineer.

81:11

Paper-Axis shutdown (during the Paper Advance test).
Requires Service Engineer

85:10

Paper-Axis Encoder error. The Drive Roller Encoder Sensor cannot find the zero position of the Encoder Disk.
Requires Service Engineer

86:01

Scan-axis shutdown/Carriage Servo shutdown - caused by problem moving the carriage, most likely due to a paper jam.

Try the following: 

  • Switch the Power OFF from the back of the Printer and disconnect the Power cord. 
  • Open the Window and check for any visible obstacles restricting the movement of the carriage. If there is a wrinkled mass of media inside the paper path, lift the Pinch wheels (using the Media Lever) and clear the obstruction.
  • Reconnect the power cord and power ON the Printer.

If problem persists - Requires Service Engineer

86:11

View onView on YouTube

Scan-Axis length too short.

  • Open the Window and check for any visible obstacles restricting the movement of the Carriage Assembly.
  • If there is a wrinkled mass of media inside the paper path, lift the Pinchwheels (using the Media Lever) and clear the obstruction. 

Requires a Service Engineer if error code recurs.

86:13

Carriage-Axis shutdown (Firmware Error).
Switch the Printer Off and wait a few minutes. Switch the Printer On again and check if the Error Code has disappeared.  If the Error Code reappears, requires a Service Engineer

87:13

Unable to read the Carriage Encoder Sensor.
Switch the Printer Off and wait a few minutes. Switch the Printer On again and check if the Error Code has disappeared. If the Error Code reappears, requires a Service Engineer.

93:10

Ink System startup failed.
Requires Service Engineer