Error Codes - HP Designjet 4200 42" (A0) Scanner (Q1280A)

-1 No printer selected. 
Select a printer. A printer must be configured in the application before trying to print.

-11 The folder must be empty.  
The folder must be empty (occurs during file browsing operations).
Corrective Action: Check that the folder is empty before deleting it.

-12 Unable to delete the folder. 
Unable to delete the folder (occurs during file browsing operations, typically if a folder is shared).
Corrective Action: Close all the applications and try again.

-13 Unable to rename the folder.  
Occurs during file browsing operations, usually due to a share issue.

-14 Unable to reserve the scanner.
Check and see if any other application is using the scanner.

-16 error reading the RIP gray balance file. 
If current media profile specifies to use CSV-file in the RIP gray balance and the file is not found.
Corrective Action: Either disable the use of gray balance or attempt to create the file again.

-19 When combining thick media handling (paper guide in extended position) with auto size detection, the size detection must be done separately by running a preview scan before the final copy or scan operation. 
Corrective Action: Try the following:  Run a preview scan before the final copy or scan operation.  Perform the copy or scan to file instead

No media profile selected for current printer. 
Either select OK and then run the operation with out the Media Profile.  Or select Cancel and prepare a Media Profile before performing the operation.

No scanner selected or selected scanner not present.
If the scanner was turned Off during application start-up.

Try the following: Check that the scanner is turned On.  Check that the scanner is selected.

-9 The currently selected printer is not installed in the system.  
The windows printer driver for the currently selected printer is not found.
Try the following: Check that the printer driver is installed.  Install the printer driver if not already installed.

00003 Scanning invalid size of area requested for scanning.   
Negative scan-width specified.
Corrective Action: Reselect the scan area and try again.

01003 Error printing colorsheet.
Try the following: Check the printer to make sure it is switched On and connected to the scanner.  Try printing a test print to make sure that the printer is working. 

Call service engineer if system error code recurs.

Error detecting index-mark. 
Try restarting the system. 
If the problem persists,Call service engineer

01014 Sheet bad aligned.
Try the following: Reinsert the sheet, making sure that it is straight and at the right position.  If the problem persists - Call service engineer

01015 Error detecting left margin.
Try the following:Try reinserting the sheet. If the problem persists - Call service engineer

01016 Error detecting right margin.
Try the following: Try reinserting the sheet.  If the problem persists-Call service engineer

01017 Error reading colorsheet. The end of the sheet is reached before expected.

Check that the correct colorsheet is being used.

01018 The Close Loop Calibration (CLC) has been aborted. 
The user has cancelled the color map operation.

01019 Wrong insert position. The sheet has been inserted in the wrong position.
Try the following: Reinsert the sheet, making sure that it is at the right position.

If the problem persists, view the scandump.tif file for further diagnosis.

Call service engineer

01020  Can’t find top of sheet.  
Reinsert the sheet, making sure that it is at the right position.

01021 Can’t find bottom of sheet.
Reinsert the sheet, making sure that it is at the right position.

01022 Does not correspond to this version or clc.dll. 
Install the correct version of the language resource dll.

02 Invalid scan coordinates. The paper frame was placed fully outside the scan image. 
Try repositioning the paper frame so that it covers some of the scannable area.

02004 Unable to open device for reading.
Check that the device (file) is available.

02005 Unable to open the device for writing. 
Check that the device (file or printer) is available.

02006 Unable to read from the device.
Try the operation again.

02007 Unable to write to the device. 
Try the operation again.

02013 Destination already exists. 
Try the operation again with a different file name.

03008 Device not available. Scanner not found.
Try the following:

Check that the scanner is turned On.  Check the connection to the scanner.

06 Not enough disk space for spool file.  
Make sure that the environment TEMP (or secondary TMP) points to a folder with plenty of space.

08 The scanner is currently on standby. Please press the soft power button on the scanner to activate it. 
Press the soft power button on the scanner to activate it.

Diagnostic = Flashing, Wait = OFF, Ready = Flashes 3 times.  Error related to the switch setting on the Operators Panel. 
Check the ID switch settings on the Operators Panel: – For HP Designjet copier cc800ps: 00011000 (0=OFF, 1=ON).
For HP Designjet 815mfp: 00011011 (0=OFF, 1=ON) – For HP Designjet scanner 4200: 00100101 (0=OFF, 1=ON).
Check that the Operators Panel is correctly connected.  
The Operators Panel is faulty if this is the case then requires a Service Engineer.

Diagnostic = Flashing, Wait = OFF, Ready = Flashes 5 times.  Error related to the Smart Card. 
Check that the Smart Card is valid for this scanner.  Check that the Smart Card Reader is correctly connected to the Controller Board.
Check that the Smart Card is correctly inserted.  requires a Service Engineer.

Diagnostic = Flashing, Wait = OFF, Ready = Flashes 5 times.  Error related to the Smart Card. 
Check that the Smart Card is valid for this scanner.  Check that the Smart Card Reader is correctly connected to the Controller Board.
Check that the Smart Card is correctly inserted. if problem persists -  requires a Service Engineer.

13496 The scanner is initializing or warming up.
This happens if you try to scan too quickly after powering On the scanner. Wait a short while and then try scanning again.

17977  Media is present in scanner, but command was aborted by user.
Problem Description: User interfered with the scanner.
Try the operation again.

17980 Paper jam.  
Check rollers and mechanical paper detectors for any paper jam. Once paper jam is cleared, try the operation again.

Diagnostic = Flashing, Wait = Flashes once, Ready = OFF. Correction of Camera A failed. 
Make sure that the Glass Plate and the White Background Plate are clean.  Check the lamp to make sure that it is working.

These may be cleaned with a damp micro-fibre cleaning cloth. (do not use solvent)

If this has not resolved the problem then a Service Engineer is needed.

Diagnostic = Flashing, Wait = Flashes twice, Ready = OFF. Correction of Camera B failed.
Make sure that the Glass Plate and the White Background Plate are clean.These may be cleaned with a damp micro-fibre cleaning cloth. (do not use solvent). Check the lamp to make sure that it is working.

If this has not resolved the problem then a Service Engineer is needed.

Diagnostic = Flashing, Wait = OFF, Ready = OFF. Stitching failed (it has not been possible for the processor to detect one and only one image of the stitching wire in the scanned input).
Make sure that the Glass Plate and the White Background Plate are clean. (Do not use solvent) These may be cleaned with a damp micro-fibre cleaning cloth.

If this has not resolved the problem then a Service Engineer is needed.

Diagnostic = Flashing, Wait = OFF, Ready = Flashes twice. The connectors to the cameras are in the wrong position.

A Service Engineer is required.

Diagnostic = Flashing, Wait = OFF, Ready = Flashes twice. Error on Camera Board.
A Service Engineer is required to run further diagnostic tests to verify the faulty component.

Diagnostic = Flashing, Wait = OFF, Ready = Flashes once. Firmware related error.
This problem requires a Service Engineer.

Diagnostic = Flashing, Wait = OFF, Ready = Flashes once. Error on the Main Electronics Board.
This problem requires a Service Engineer.

Diagnostic = Flashing, Wait = OFF, Ready = Flashes 4 times. The touch screen does not detect the Scanner.
Requires a Service Engineer.

Error during initialization.  
Reboot the system and enter the BIOS setting. Load "Setup Default" and save the BIOS setting.

Call service engineer

CMOS battery failed. 
The battery life is approximately 3 years before it requires replacement. 

Call service engineer to replace CMOS battery.

Error detected in the CMOS.

Reboot the system.

Call service engineer

Problem encountered with the Touch Screen.  
Connect the Touch Screen to a CRT Monitor and check the resolution setting for the display. If the CRT Monitor is working well then it seems there is an LCD problem. 
Requires a Service engineer.

Floppy disk(s) fail (40)/ (80). No Floppy Disk detected.
Try the following: Check if the Floppy Disk Drive cable is connected correctly, reconnect the cable if necessary. 

Call service engineer

Hard Disk install failure. No Hard Disk detected, error related to Hard Disk Drive.

Call service engineer

Keyboard error or no keyboard present. No keyboard has been detected.
Try the following: Check if the Keyboard is connected correctly. Reconnect the cable if necessary. Replace the Keyboard if all else fails 

Memory test fail. 

Requires a Service Engineer.

Primary master hard disk fail. No Hard Disk detected, error related to Hard Disk Drive.

Call service engineer

Primary slave hard disk fail. No Hard Disk detected, error related to Hard Disk Drive.

Call service engineer

Secondary master hard disk fail No Hard Disk detected, error related to Hard Disk Drive.

Call service engineer

Secondary slave hard disk fail. No Hard Disk detected, error related to Hard Disk Drive.

Call service engineer

The system cannot read from the CD-ROM drive.
Eject the CD currently in the CD-ROM drive and place it into a different CD-ROM drive. Can the CD be read in the other CD-ROM drive?
If Yes:  Requires a Service Engineer.
If No: Replace the CD, it could be damaged.

The driver is not ready - The system cannot read from the Floppy Disk Drive (FDD).

Try the following: Eject the Floppy Disk currently in the FDD and place it into a different FDD. Can the CD be read in the other FDD? – If Yes: Replace the Floppy Disk Drive (P/N Q1278-60035). – If No: Replace the Floppy Disk, it could be damaged.