Skip to content

sales@wideimagesolutions.com

Phone Number: +1 (214) 727 6289                             WhatsApp Number: +1 (214) 727-6289
Please use email 99% of the time as it is now very difficult to answer all the phone calls.
Email: sales@wideimagesolutions.com    Phone Number: +1 (405) 927-8129       WhatsApp Number: +1 (214) 727-6289.
Please use email 99% of the time as it is now very difficult to answer all the phone calls.

Error Codes - Designjet T1300 44'' (A0) Printer (CR651A)

*Enjoy fast, quality A0 printing with 2 roll smart switching & true print previews*

60.2:YZ

Initialisation error.

  • Switch the power OFF from the back of the printer and disconnect the power cord.
  • Check that the printer is properly connected in all other respects.  
  • Wait 2 minutes then reconnect the power cord and power ON the printer. 

 

If error continues then requires a Service Engineer.

01.0:YZ

Communication with Main PCA failed.
Try the following: Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power ON the Printer.

If this does not resolve the problem - Requires Service Engineer

01.1:YZ

Error in the Engine PCA
Switch the power off from the rear of the unit and disconnect the power cord. Reconnect power cord and power on the unit if problem persists.
Requires a Service Engineer

01.2:YZ

Failure  communicating with an Ink Supply
Switch the power off from the rear of the unit and disconnect the power cord. Reconnect power cord and power on the unit if problem persists.
Requires a Service Engineer

02.1:YZ

Problem with the Carriage PCA. 
Try the following: Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power ON the Printer. If this does not work check that the Trailing Cable is not damaged. If this does not resolve problem - Requires Service Engineer 

 

03.0:10

Battery of Real Time Clock has run down.

 Requires Service Engineer 

03:YZ

Problem with Power Supply Unit.
Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power ON the Printer. If error continues requires Service Engineer.

06:YZ

Failure reading/writing NVM in Hard disk.

Try the following: Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer.

If the System Error continues call Service Engineer

07.01:11

eDelSol3 ASIC not found or not responding.

Requires a Service Enginer

07.02:11

USB cable not connected.
Requires a Service Engineer

07.03:10

USB Hub not found.
Requires a Service Engineer

07.03:11

USB Scanner connected to incorrect port.
Requires a Service Engineer

07:10

Interconnect Board or Power Cable has failed.
Check that power cable connection and condition, replace if necessary.
Requires a Service Engineer

08.01:11

Touch Control Panel USB Cable fails.
Requires a Service Engineer

08:04

Touch Control Panel communication to the product functions at the initialisation, but during normal working is lost.
Recycle power if problem persists. 
Requires a Service Engineer

08:08

A feature on the Touch Control Panel hangs or will not function (copy, scan etc.)
Recycle power if problem persists.
Requires a Service Engineer

08:11

No communication between the product and the Touch Control Panel.
Recycle power if problem persists.
Requires a Service Engineer

09.01:10

Scanner motor failure.
Requires a Service Engineer

09.02:10

CIS A Element failure.
Requires a Service Engineer

09.03:10

CIS B Element failure.
Requires a Service Enginee

09.04:10

CIS C Element failure.
Requires a Service Enginee

09.05:10

CIS D Element failure.
Requires a Service Engineer

09.06:10

CIS E Element failure.
Requires a Service Engineer

09.08:11

Power cable of Scanner failure.
Requires a Service Engineer

09.09:11

USB cable of Scanner failure. 
Requires a Service Engineer 

09.10:04

Scanner in safe mode

Restart the product, if system error code continues call service engineer

09.10:10

Scanner SCU failure.
Requires a Service Engineer

09:01

Media jam in Scanner.
Open CIS to remove media jam

If no jam found - Requires a Service Engineer

09:02

Scanner not calibrated.
Requires Service Engineer.

09:03

File I/O Error.
Recycle power if problem persists.
Requires a Service Engineer

09:04

Contex Library failed to load.
Recycle power if problem persists.
Requires a Service Engineer

11:YZ

Trailing Cable does not seem to be detected.
Try the following: Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power ON the Printer. Check that the Trailing Cable is not damaged. If this does not resolve the problem - Requires Service Engineer

21.1:YZ

Failure moving the Primer Motor of the Service Station.
Requires Service Engineer.

21.2:YZ

Failure testing the length of the Service Station path.

  • Switch the power off from the back of the printer and disconnect the power cord.
  • Check the Primer Tubes.
  • Make sure that the Service Station path is clear. Remove any visible obstacles (paper, screws, plastic parts, etc.) restricting the movement of the Service Station.  
  • Reconnect the power cord and power on the printer.  

 

If error continues then requires a Service Engineer.

21:YZ

Failure moving Service Station. 
Try the following:
● Switch the Power OFF from the back of the Printer and disconnect the Power cord. Check the Primer Tubes. 
● Make sure that the Service Station path is clear. Remove any visible obstacles (e.g.paper,  screws, plastic parts, etc...) restricting the movement of the Service Station.

● Reconnect the power cord and power ON the Printer.

If error continues then requires a Service Engineer.

22.0:YZ

Left Ink Supply Error, module 0.
Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power ON the Printer.
If problem continues, requires a Service Engineer.

22.1:YZ

Left Ink Supply Station error.
Try the following: Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power ON the Printer.

If this does not resolve the problem - Requires Service Engineer

24:YZ

Ink Setup failure. 
Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power ON the Printer.
If problem continues, requires a Service Engineer.

26:01

Ink supply error found during IDS diagnostic test. In the Touch Control Panel you wil see letters reresenting the names of the colours of the faulty supplies.

  • Reseat the faulty ink supply and repeat the Ink Delivery System diagnostic test.
  • If the problem persists, replace the faulty ink supply and repeat the Ink Delivery System diagnostic test.  

If error continues then requires a Service Engineer.

39.1:01

Roll 1 switch failed (standby or resume). Roll 1 has been unloaded.
There is no corrective action for this. This system warning code only notifies the user that the roll has been unloaded because an unexpected error occured with Roll 1 in standby or resume operation. If problem persists, Requires a Service Engineer

39.2:01

Roll 2 switch failed (standby or resume). Roll 2 has been unloaded.
There is no corrective action for this. This system warning code only notifies the user that the roll has been unloaded because an unexpected error occured with Roll 1 in standby or resume operation. If problem persists, Requires a Service Enginee

41:YZ

Electrical fault or current limit in Media-Axis Motor.
Try the following:

  • Switch the Power OFF from the back of the Printer and disconnect the Power cord.
  • Open the Window and check for any visible obstacles restricting the movement of the Media Advance Roller. If there is a wrinkled mass of media inside the paper path, lift the Pinch wheels (using Media Lever) and clear the obstruction. 
  • Reconnect the power cord and power ON the Printer. 
  • If the problem persists - Requires Service Engineer

42:YZ

Electrical problem (fault, current limit, overheating) in Scan-Axis Motor.
Try the following:

  • Switch the power off from the rear of the unit, disconnect the power cable.
  • Check for any visable obstacles restricting movement of Carriage Assembly. Remove any obstacle to let the carriage move freely along the whole scan-axis. If there is a wrinkled mass of paper inside the paper path, raise the pinch wheels (using the Media Lever) and clear the obstruction.  
  • Reconnect and power on the unit
  • If problem persists - Requires a Service Engineer

45.1:YZ

An error with the Rewinder 1 System (Upper Rewinder) has been detected.

  • Switch the power off from the rear of the unit, disconnect the power cable.
  • Remove the paper from Roll 1.
  • Reconnect and power on the unit,

If problem persists. Requires a Service Engineer

45.2:YZ

An error with the Rewinder 2 System (Lower Rewinder) has been detected.

  • Switch the power off from the rear of the unit, disconnect the power cable.
  • Remove the paper from Roll 2.
  • Reconnect and power on the unit, if problem persists.

Requires a Service Engineer

47:YZ

Star wheels motor error.

Try the following:

  • Switch the Power OFF from the back of the Printer and disconnect the Power cord. 
  • Check that the Starwheel Assembly cable is not damaged and is correctly connected to Main PCA.
  • Open the Window and check for any visible obstacles restricting the movement of the Starwheel Assembly, then clear the obstruction.
  • Reconnect the power cord and power On the Printer.

If error persists, may require a Service Engineer

48:YZ

PPS system failure.
Try the following: Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power ON the Printer.

If the problem persists - Requires Service Engineer

51:YZ

Scanner Position Sensor failure.
Requires a Service Engineer

52:10

The printer has detected a failure in the Drop Detector.
Try the following: Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power ON the Printer.

If the problem persists - Requires Service Engineer.

55:YZ

Problem with the Line Sensor (Tetris). The printer has detected a failure to access Line Sensor EEPROM).

Try the following: Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power ON the Printer.If the problem persists - Requires Service Engineer.

56:YZ

Drive Roller analog encoder homing (also known as "zero search") failed.
Switch the power off from the rear of the unit, disconnect the power cable. Reconnect and power on the unit, If problem persists. Requires a Service Engineer

59.1:09

Two electrical parts have been replaced at the same time.
Requires a Service Engineer

59.2:00

An unsupported or used part has been installed.
Requires a Service Engineer

60.1:YZ

Initialisation error.

  • Switch the power OFF from the back of the printer and disconnect the power cord.
  • Check that the printer is properly connected in all other respects.  
  • Wait 2 minutes then reconnect the power cord and power ON the printer. 

If error continues then requires a Service Engineer.

61:04.1

The PostScript fonts seem to be missing.
Requires a Service Engineer to Perform a firmware upgrade to re-install the fonts.

61:08.1

The file cannot be printed because it is password protected.
Resend the file without password protection, if problem persists Requires a Service Engineer

61:YZ

The file format is incorrect or not supported for the current product configuration and the product cannot process the job.

  • Check whether the printer supports the file format (formats such as PS, PDF, TIFF and JPEG are supported by PostScript printers only).  
  • Switch the power OFF from the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer.  
  • Resend the file to the printer. 

 

If error continues then requires a Service Engineer.

63:01

Cannot retrieve IP address.
Requires a Service Engineer

63:YZ

Input/Output problem through the network interface of the formatter. 
Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power ON the Printer. 
If the error continues, requires a Service Engineer.

64.1:YZ

The External Hard Disk accessory does not seem to be connected.
Requires a Service Engineer

64:YZ

Input/Output problem through the USB Port
Try the following:
● Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power ON the Printer.
● Check that the USB cable is correctly connected to the Printer.
● Check that the Printer has the latest Firmware version. If not Require a Service Engineer to update the Firmware to the latest version.

65:YZ

Memory Driver Internal I/O error, I/O Socket Manager Internal I/O error, communications error.

Try the following:

  • Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer.
  • Check that the unknown port cable is correctly connected to the Printer.
  • Check that the Printer has the latest Firmware version. If not, update the Firmware to the latest version.

Requires Service Engineer.   

68:YZ

Loss of engine counters tracking. 
Try the following:
● Reboot the printer. The printer will continue to function correctly, but the life counters will not continue counting until you restart the printer.
Requires a Service Engineer.

71:03

Out of Memory.
Restart the product, if problem persists Requires a Service Engineer

71:04

Out of Memory.
The total memory available in the product depends upon its configuration. It is reported as HP-GL/2 memory or PS/PDF memory. If the amount of memory that the product needs to process the file is more than the amount available, the unit will display this system warning. The amount of memory required for processing the file is known as the 'display list memory'  This should not be confused with the file size of the print job.  Try reducing the resolution of the file to be printed if this does not resolve the issue, Requires a Service Engineer

72.02:09

Generic firmware Error.
Restart the product, if problem persists unit may require a firmware update Requires a Service Engineer

72.02:YZ

A Service Callibration should be performed.
Requires a Service Engineer

74.08:04

Problem with the Firmware upgrade process.
Requires a Service Engineer

74.1:YZ

Error uploading paper profile update file

Try the following:

  • Switch the power off from the back of the product and disconnect trhe power cord. Reconnect the power cord and power on the product.
  • Make sure the connection between the computer and the product is functioning correctly.
  • Try to upload the paper profile update file again. make sure the version of the paper profile update file is compatible with the Firmware version the product is using. You can check this on the same Web Page from where you downloaded the paper profile update.
  • A service engineer should not be required unless the error code recurs.

74:YZ

Error uploading firmware update file. 
Try the following:
● Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power ON the Printer.
● Make sure the connection between the computer and the printer is functioning properly.
● Try to update the Firmware again.
May require a Service Engineer.

75.21:YZ

The Spitoons (Left Spitton, Service Station) have reached 80% capacity.
Requires Service Engineer.

75.22:YZ

The Spitoons (Left Spitton, Service Station) are full.
Requires Service Engineer

76:YZ

Hard Disk drive is full

Remove any unnecessary files from the hard disk using the Embedded Web server.

If the problem persists run the Hard Disk recovery facility - May require a Service engineer

78.1:YZ

Media settings area missing in media settings file
Try the following: 

  • Switch the Power OFF from the back of the Printer and disconnect the Power cord.
  • Reconnect the power cord and power On the Printer.  
  • Firmware may need updating
  • Update the OMES of the paper type that is failing.

Requires Service Engineer.

78:08

The job received can not be printed without borders on this paper.

Try the following:

Use a paper that supports borderless printing.

This system error code does NOT require service help. It should be resolved by the customer.

79:YZ

Generic Firmware error.

Try the following:

  • Switch the Power OFF from the back of the Printer and disconnect thePower cord. Reconnect the power cord and power On the Printer.
  • Check that the Printer has the latest Firmware version. If not, update the Firmware to the latest version.

If this does not resolve the problem - Requires Service Engineer.

81:01

Paper axis error - the copier will restart and run a diagnostic test.

81:YZ

This Error can occur if the product has been dropped during transportation causing structural damage.

Before continuing with the 81:YZ troubleshooting, first look for structural damage. e.g.Consistent 81:YZ error codes.

May require a Service Engineer

86:01

Scan-axis shutdown/Carriage Servo shutdown - caused by problem moving the carriage, most likely due to a paper jam.

Try the following: 

  • Switch the Power OFF from the back of the Printer and disconnect the Power cord. 
  • Open the Window and check for any visible obstacles restricting the movement of the carriage. If there is a wrinkled mass of media inside the paper path, lift the Pinch wheels (using the Media Lever) and clear the obstruction.
  • Reconnect the power cord and power ON the Printer.

If problem persists - Requires Service Engineer

86:11

Scan axis movement requires too much force or energy.
Requires a Service Engineer

87:01

Problem finding the Scan-axis encoder reading.
Switch the power OFF from the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer. 
If problem continues requires a Service Engineer.

87:YZ

Problem finding the Scan-axis/Carriage sensor encoder reading.

Try the following:

  • Switch the Power OFF from the back of the Printer and disconnect the Power cord.
  • Reconnect the power cord and power ON the Printer.
  • Movement jam - possible paper jam.
  • Check that the Scan-Axis Motor is correctly connected.
  • Check that the Encoder Sensor is correctly connected.
  • Remove the Encoder Strip and clean it.

Requires a Service Engineer.

93:YZ

Unable to pressurize the Ink Delivery System. The ISS Motor does not move as expected

Try the following: 

Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power ON the Printer.

If Problem persists - Requires Service Engineer.